Gortite® Sewn bellows are manufactured from heavy-duty elastomer-coated fabric stitched with nylon or specialty thread. A liquid coating can be added to seams to extend life in severe applications by reducing the thread exposure to the environment or to limit moisture leakage. Available in any size or shape (round, oval, box, way cover, etc.) without tooling charges.
Sewn bellows help keep abrasive grit, impinging chips, and coolant off of machine ways and ball screws. Sewn bellows boots are ideal for protecting hydraulic cylinder rods, shafts and splines. Using a bellows cover is essential for mitigating damage to actuators and motion components, thus maintaining uptime.
Large crane rigs often feature hydraulic cylinders, which are required to operate with long service life between maintenance and inspection periods.
Bellows shown below is “4 stories” tall (drilling equipment)
Shaft protection:
Screw protection:
Typical Materials:
Before filling out PDF forms, download/save and open in Adobe Reader.
Way Cover – Replacement Design (PDF)
Completing the Dynatect Enclosed Shaped Bellows Quote Request Form
Collecting Measurements for a Way Cover Quote Request
Get a Quote on a Replacement Way Cover
Here are the legacy part numbers representing common rod boot sizes of Gortite® Sewn Bellows made from neoprene-coated nylon fabric.
| ROD BOOT STYLE | Inside Diameter (ID) | Outside Diameter (OD) | Retracted Length every 12″ section | Available Inner Diameter (I.D.) Sizes |
| SRA-15 | 3/4″ | 3″ | 3/4″ | 1/2″ to 3″ |
| SRB-15 | 1-1/8″ | 3-3/8″ | 3/4″ | 1/2″ to 3-3/8″ |
| SRC-15 | 1-1/2″ | 3-3/4″ | 3/4″ | 1/2″ to 3-3/4″ |
| SRD-15 | 1-7/8″ | 4-1/8″ | 3/4″ | 1/2″ to 4-1/8″ |
| SRE-15 | 2-3/8″ | 4-5/8″ | 3/4″ | 1/2″ to 4-5/8″ |
| SRF-15 | 2-7/8″ | 5-1/8″ | 3/4″ | 1/2″ to 5-1/8″ |
| SRG-25 | 3-3/8″ | 7″ | 1/2″ | 1/2″ to 7″ |
| SRH-25 | 3-7/8″ | 7-1/2″ | 1/2″ | 1/2″ to 7-1/2″ |
| SRJ-25 | 4-1/2″ | 8-1/4″ | 1/2″ | 1/2″ to 8-1/4″ |
| SRK-25 | 5″ | 8-3/8″ | 1/2″ | 1/2″ to 8-3/8″ |
| SRM-25 | 5-3/8″ | 9-1/2″ | 1/2″ | 1/2″ to 9-1/2″ |
| SRO-25 | 7-1/4″ | 11″ | 1/2″ | 1/2″ to 11″ |
Mounting Accessories: Clamps (for end collars) or Back-up mounting plates (for flange ends) can be added to your order upon request
Sewn Rod Boot Bellows Request for Quote
1. Stock boot part number
2. Outer diameter (O.D.) of part to be covered
3. Travel distance or extended length (note: ends excluded) Stock bellows are available in 12″ extended length increments
4. Specify type of end: Do you want a standard flange or a collar?
For Collar End: Specify collar width and collar I.D. (inner diameter)
For Flange End: Specify Flange I.D. (inner diameter) and Flange O.D. (outer diameter)
5. Specify mounting options:
a. C208 Clamp: stocked in any size required, clamp band is 1/2” wide, minimum 1/2” I.D. – specify in 1/8” increments.
b. C205 flange back-up plate: shipped blank. If mounting holes are desired, please send sketch indicating bolt hole pattern and size.
Use our contact page to get in touch with us directly for placing an order, requesting a quote, or getting your products repaired.
Use Our Contact Form
